D15b into 95 Cx
13-Nov-2009, 11:43 PM
#21
I started my swap tonight and everything was going great until I came across a sensor located on the engine block on the left side if your sanding in front of the car hidden by the valve cover, i tried to undo it and it broke 
what can I do?
Is there places that sell them local, and will me new egine start if I dont get one in time?
Thanks
what can I do?Is there places that sell them local, and will me new egine start if I dont get one in time?
Thanks
14-Nov-2009, 08:33 AM
#23
that's just it im not sure what it is but I doesn't look to be the oil pressure sensor. all i know is it right under the distributor. Ill take a pic of it and post it when i get back to the shop....if they have wifi
14-Nov-2009, 09:00 AM
#24
its probably a coolant temperature sensor.
Is it the 2-wire sensor or the 1-wire sensor?
Either way to 2 sensors on the side of the head under the dizzy are both coolant temp sensors.
Is it the 2-wire sensor or the 1-wire sensor?
Either way to 2 sensors on the side of the head under the dizzy are both coolant temp sensors.
14-Nov-2009, 09:52 PM
#26
Swap update
JDM d15b vtec in the engine bay 
Now here are my last problems. I didn't mark this hose and I don't know where it goes please help cause I am clueless. (the one I am pointing too...top hose)
orange plug that came off my old engine
I know it came from here on my old engine
but as you can see on my new engine there is a bolt in that location...what am I to do..also the new d15b was auto now is a 5spd I don't know if that has anything to do with it.
please help, and thanks for all of your time
Now here are my last problems. I didn't mark this hose and I don't know where it goes please help cause I am clueless. (the one I am pointing too...top hose)
orange plug that came off my old engine
I know it came from here on my old engine
but as you can see on my new engine there is a bolt in that location...what am I to do..also the new d15b was auto now is a 5spd I don't know if that has anything to do with it.
please help, and thanks for all of your time
15-Nov-2009, 11:37 AM
#28
15-Nov-2009, 08:03 PM
#30
swap update part2
I got the car started and its at my house right now
only a few issues left with the swap.
1. I put in the new p28 ecu and my temp gauge doesnt work?
2. The rad fan also doesnt work?
3. Since my d15b didnt come with the distributor, I use the stock cx one and it runs ruff...will get the correct one this week ( not driving the car until I get it )
4.There is one harness wire that has no place to connect near the far right side of the intake manifold. the old cx had some type of sensor on the top right of the intake manifold (thats where it connected) but the d15b does not... what to do?
I figured out the orange wire porblem its just my old block heater wire so im not going to use it.. problem sloved
if theres anyone that has done a d15b swap and is wiling to see if everything is good with my swap or able to help me out with the problems listed please let me know.
Thanks again
only a few issues left with the swap.
1. I put in the new p28 ecu and my temp gauge doesnt work?
2. The rad fan also doesnt work?
3. Since my d15b didnt come with the distributor, I use the stock cx one and it runs ruff...will get the correct one this week ( not driving the car until I get it )
4.There is one harness wire that has no place to connect near the far right side of the intake manifold. the old cx had some type of sensor on the top right of the intake manifold (thats where it connected) but the d15b does not... what to do?
I figured out the orange wire porblem its just my old block heater wire so im not going to use it.. problem sloved
if theres anyone that has done a d15b swap and is wiling to see if everything is good with my swap or able to help me out with the problems listed please let me know.
Thanks again
Thread
Thread Starter
Forum
Replies
Last Post
malek_eg
Honda Civic Performance - JDM Discussion
10
04-Jan-2007 08:08 AM
imported_P-O-G-I
Honda Civic Performance - JDM Discussion
9
16-Aug-2004 10:26 AM
