B16a2 into 5th gen.
#45
ok, now im fucked
i have absolutly no idea what motor is what ...
i dont even know what i want now....
i wanted a b16a2 b/c they had a 170 hp
but now i dont know if they do or not....
just tell me this,, WHAT ONE SWAPS DIRECTLY INTO THE 5TH GEN....
i have absolutly no idea what motor is what ...
i dont even know what i want now....
i wanted a b16a2 b/c they had a 170 hp
but now i dont know if they do or not....
just tell me this,, WHAT ONE SWAPS DIRECTLY INTO THE 5TH GEN....
#46
Ok, I've asked around locally in Windsor to see what shops are looking for to put in an A2, and this is what I got back.
"The engine costs $3500.00, includes trans, ECU, complete engine assembly. You will need a Del Sol rear transmission bracket, 94 Del Sol VTEC axles and half-shaft, a little bit of wiring conversion, and lots of labour.
You will probably want to do a clutch while its out, and maybe headers too, but you can leave the JDM ones to save money.
The whole swap will cost at least $5000.00, by the time you get all the parts you need, plus the labour to install it.
The B16A1 does NOT WORK because it has a cable transmission instead of hydraulic, and the engine mounts do not line up, and it is 10HP less then the A2 anyways.
If you don't have the car yet, get an Si for the extras, like the power roof, power mirrors and rear disc brakes, you will need them to stop the car after the engine is in.
Approximate 1/4 mile times with the swap are 15.2-15.5, and with a ZEX 75HP nitrous kit, you should be able to get down to 14.2-14.5 or so, obviously with a good clutch."
Does this sound about right?
So bascilly I need all kinds of new axles and **** to make this engine work, thefore its not a DIRECT swap, correct?
"The engine costs $3500.00, includes trans, ECU, complete engine assembly. You will need a Del Sol rear transmission bracket, 94 Del Sol VTEC axles and half-shaft, a little bit of wiring conversion, and lots of labour.
You will probably want to do a clutch while its out, and maybe headers too, but you can leave the JDM ones to save money.
The whole swap will cost at least $5000.00, by the time you get all the parts you need, plus the labour to install it.
The B16A1 does NOT WORK because it has a cable transmission instead of hydraulic, and the engine mounts do not line up, and it is 10HP less then the A2 anyways.
If you don't have the car yet, get an Si for the extras, like the power roof, power mirrors and rear disc brakes, you will need them to stop the car after the engine is in.
Approximate 1/4 mile times with the swap are 15.2-15.5, and with a ZEX 75HP nitrous kit, you should be able to get down to 14.2-14.5 or so, obviously with a good clutch."
Does this sound about right?
So bascilly I need all kinds of new axles and **** to make this engine work, thefore its not a DIRECT swap, correct?
#47
if want to save some cash now.. you can use the b16a1 "motor" and just bolt on a b series tranny... maybe the money you save on the motor you could splurge and get a type r tranny....
i believe you can do that anyways?? putting a hydro tranny on a b16a1??
i believe you can do that anyways?? putting a hydro tranny on a b16a1??
#48
Guest
Posts: n/a
Originally posted by Happy???
You are just going to confuse more people now with this information because now you are comparing a B16a2 to a 1st gen b16a motor. YES - these two are for the better part equal. As mentioned there are small add-on here and there but for the most part equal.
BUT, I thought the conversation at hand was the difference between the b16a2 and the 2nd Gen b16a.
These two motors ARE NOT EQUAL. They have different internals!
The b16a2 uses a PR3 piston while the 2nd Gen B16a uses a higher dome P30 piston.
You are just going to confuse more people now with this information because now you are comparing a B16a2 to a 1st gen b16a motor. YES - these two are for the better part equal. As mentioned there are small add-on here and there but for the most part equal.
BUT, I thought the conversation at hand was the difference between the b16a2 and the 2nd Gen b16a.
These two motors ARE NOT EQUAL. They have different internals!
The b16a2 uses a PR3 piston while the 2nd Gen B16a uses a higher dome P30 piston.
hopefully: it is a direct swap. yeah you need new axles but these will fit without any problems. go for it. that shop's message made it sound a little more complicated than it is. there's about 100 peopel on this board with B16a's in 5th gen hatches. it's not a hard swap. Geez.. Altech does about 5 of these every week.
#49
Guest
Posts: n/a
Originally posted by 90EFHB
So how much are we going to slice the hair? If it comes with english writing stickers as opposed to japanese?
If they are are the same internally is that not the same engine
So how much are we going to slice the hair? If it comes with english writing stickers as opposed to japanese?
If they are are the same internally is that not the same engine
#50
Originally posted by Jugglez
thank you, exactly what i was about to post.
hopefully: it is a direct swap. yeah you need new axles but these will fit without any problems. go for it. that shop's message made it sound a little more complicated than it is. there's about 100 peopel on this board with B16a's in 5th gen hatches. it's not a hard swap. Geez.. Altech does about 5 of these every week.
thank you, exactly what i was about to post.
hopefully: it is a direct swap. yeah you need new axles but these will fit without any problems. go for it. that shop's message made it sound a little more complicated than it is. there's about 100 peopel on this board with B16a's in 5th gen hatches. it's not a hard swap. Geez.. Altech does about 5 of these every week.
#53
Originally posted by Jugglez
you said they're "exact same". one has an oil cooler, one doens't. that doesn't make them the same. the OEM oil cooler is worth $500 - i'd say that's a pretty big difference.
you said they're "exact same". one has an oil cooler, one doens't. that doesn't make them the same. the OEM oil cooler is worth $500 - i'd say that's a pretty big difference.
#55
Originally posted by 94EG6HB
You back fast Dave..
You find D??
You back fast Dave..
You find D??
Car is there getting a tune up.
I recommend everyone use Buddah's services for tuneup's etc. I knwo gatherer, 94EG6HB and I are all happy.
#56
You asked around WINDSOR?? What, you asked SOS?? LOL Not a single shop in town knows their ****... SOS may be able to put a motor in, but my retarded neighbour can do that... it's a matter of tuning... just save yourself the headache and get Altech to do the work.
#57
Originally posted by 90EFHB
I assume Buddah is what you are speaking of.....yes he was at the shop and his phone was at home....
Car is there getting a tune up.
I recommend everyone use Buddah's services for tuneup's etc. I knwo gatherer, 94EG6HB and I are all happy.
I assume Buddah is what you are speaking of.....yes he was at the shop and his phone was at home....
Car is there getting a tune up.
I recommend everyone use Buddah's services for tuneup's etc. I knwo gatherer, 94EG6HB and I are all happy.
#58
Originally posted by bbarbulo
You asked around WINDSOR?? What, you asked SOS?? LOL Not a single shop in town knows their ****... SOS may be able to put a motor in, but my retarded neighbour can do that... it's a matter of tuning... just save yourself the headache and get Altech to do the work.
You asked around WINDSOR?? What, you asked SOS?? LOL Not a single shop in town knows their ****... SOS may be able to put a motor in, but my retarded neighbour can do that... it's a matter of tuning... just save yourself the headache and get Altech to do the work.
Can you ask him how many versions on the B16 is there?