EG (92-95) Picture Post
#102
I've already posted here but I'll do it again
Quick question does anyone know a good place to find tripods for digi cams?
**** Can anyone see the pics, or is it just me. I dont know why on my comp they show up as a red x, there uploaded on imagestation***
Quick question does anyone know a good place to find tripods for digi cams?
**** Can anyone see the pics, or is it just me. I dont know why on my comp they show up as a red x, there uploaded on imagestation***
#106
#115
Photoshopped the colours ...n the banner..thas all...
leme know what you guyz n gals think
This file below is for the guy with the redEG since u spotted me and complimented my ride...I felt obliged.. plus I had time and I was bored..
I agree with the rest..u should drop the car and put a back skirt..
At the same time I respect what youve done cuz I dont like it either when ppl tell me what to do with my car..
leme know what you guyz n gals think
This file below is for the guy with the redEG since u spotted me and complimented my ride...I felt obliged.. plus I had time and I was bored..
I agree with the rest..u should drop the car and put a back skirt..
At the same time I respect what youve done cuz I dont like it either when ppl tell me what to do with my car..
#116
Well, here's my slow POS. Enjoy Yourself :P
Foggies n CF. YUMM!
Swap. MaD TyTe JdM Yo!!11!1 (Fully Built LS/VTEC)
Spoon N1.. Yes its real.
Dubbin.
Green Grass isn't it?
My Side.
Car Wash Pimp.
****ed up contrast. buahaha.
Motor Mods:
- 94 LS bottom end
- 99 GSR head
- Skunk2 Stage 2 Pro's
- Skunk2 Titanium Retainers/Valvesprings
- Skunk2 Cam Gears
- Skunk2 Pro Series IM Hogged out to 70mm
- 2.5 Mandrel to a Spoon N1 Axle-back
- CTR N1 crank pulley
- JE 12.5:1 pistonswith upgraded rings
- PROBE ultra light rods
- Exedy lightweight flywheel
- Exedy Organic Clutch
- Balanced rotating assembly
- Micro-polished crankshaft
- new OEM Honda bearings, seals, gaskets, water pump, TBelt, the works
- 450 CC DSM injectors
- ODB1 harness all setup with resistor box and injectors
- B16a2 Tranny
- Hondata stage 2 in odb1 GSR ECU, with a base map to run the motor.
Foggies n CF. YUMM!
Swap. MaD TyTe JdM Yo!!11!1 (Fully Built LS/VTEC)
Spoon N1.. Yes its real.
Dubbin.
Green Grass isn't it?
My Side.
Car Wash Pimp.
****ed up contrast. buahaha.
Motor Mods:
- 94 LS bottom end
- 99 GSR head
- Skunk2 Stage 2 Pro's
- Skunk2 Titanium Retainers/Valvesprings
- Skunk2 Cam Gears
- Skunk2 Pro Series IM Hogged out to 70mm
- 2.5 Mandrel to a Spoon N1 Axle-back
- CTR N1 crank pulley
- JE 12.5:1 pistonswith upgraded rings
- PROBE ultra light rods
- Exedy lightweight flywheel
- Exedy Organic Clutch
- Balanced rotating assembly
- Micro-polished crankshaft
- new OEM Honda bearings, seals, gaskets, water pump, TBelt, the works
- 450 CC DSM injectors
- ODB1 harness all setup with resistor box and injectors
- B16a2 Tranny
- Hondata stage 2 in odb1 GSR ECU, with a base map to run the motor.