Knuckle Question
#1
Knuckle Question
I have a 94 EG cx I am doing the integra front brake swap, and yesterday I had my new Lower balljoint pressed in and I used a 2001 integra GSR balljoint. Right now I try to install it , everything is fine except that the knuckle would not connect with the upper control arm. The whole knuckle is tilting from the inside...what should I do? If was fine few days ago when I try em on. Thanks...please help.
#2
all balljoints in eg ek da and dc2 platforms should be the same size and taper. so you are doing something wrong.... double check your work. I'm not sure what you mean the knuckle is tilting from the inside? that confuses me
#7
if you can't get it in, remove the lower shock bolt from the fork so you can drop the lower control arm a lil more to give you extra clearance so you can pop the upper control arm into place.
#10
ok so you have the LCA attached and now you can't push it into place so it can attach to the UCA. yeah, then I would bet the axle is separated. seat the axle first, make sure it's well engaged and then try again. best of luck. going for girls and beers now.... ttyl and good luck
#14
frustration is just part of working on your car, it's the end result that makes you feel like the man. lil problems can only be expected. just remember, it's all just nuts and bolts, don't let it own you. seems to me your problem is quite simple... you'll feel the axle seat itself as it pops into place, that's how you know you've conquered it. let us know how it all works out for you
#15
man jsut bend that **** back...I mean I coudl move my **** around fine...just use some muscle and bend it to the upper control arm...it's suppose to be able to move around abit when the lower ball joint is in....just grab the knucle and push it till it lines up.
I jsut did mine last weekend and that's what I did so,....your axle seems seated fine...your could also try putting the upper in then tryin to seat the lower..
I jsut did mine last weekend and that's what I did so,....your axle seems seated fine...your could also try putting the upper in then tryin to seat the lower..
#16
Oh ****, you're doing this swap yourself??? I thought you told me you're getting some shop to do it!!
If you need any help, you can add the email address you were emailing me at before to your msn.
If you need any help, you can add the email address you were emailing me at before to your msn.
#17
Torrey: Thanks dude, I am alomost done just been busy with exams and other stuff. Waiting for a new tie rod end and alignment then Im done. The swap is not hard but since it's my first time its a little frustrating.
#18
Originally posted by dingus88
man jsut bend that **** back...I mean I coudl move my **** around fine...just use some muscle and bend it to the upper control arm...it's suppose to be able to move around abit when the lower ball joint is in....just grab the knucle and push it till it lines up.
I jsut did mine last weekend and that's what I did so,....your axle seems seated fine...your could also try putting the upper in then tryin to seat the lower..
man jsut bend that **** back...I mean I coudl move my **** around fine...just use some muscle and bend it to the upper control arm...it's suppose to be able to move around abit when the lower ball joint is in....just grab the knucle and push it till it lines up.
I jsut did mine last weekend and that's what I did so,....your axle seems seated fine...your could also try putting the upper in then tryin to seat the lower..
Thread
Thread Starter
Forum
Replies
Last Post
thepiratebay
Honda Civic Performance - JDM Discussion
10
24-Mar-2007 11:38 PM
imported_jonny_emo
Honda Civic (+ other) Parts/Accessories for Sale or Trade
3
10-Apr-2006 09:59 PM
phil1907
Honda Civic (+ other) Parts/Accessories for Sale or Trade
1
01-Jan-2006 07:25 PM