99 - 00 Civic SIR to Auto conversion
I was wondering if anyone has swapped out the tranny in a 99-00 SIR for a Auto tranny. What kind of tranny would be good? (Prelude?) Looking for it as a daily driver and just thought Auto would be better. Any inputs?
|
u wanna make an SiR auto????
|
:richslap:
what else can i say? you live in ottawa it's not like you have to deal with Toronto rushhour traffic either? i do that many days and i still have stick... if you want auto get an Si, or Dx, or Cx .. :tsk: and back to your question, would they even have a tranny that fit that engine?.... and even if they did wouldn't there be a **** load of problems with the ecu etc...? |
wow, i guess theres a first for everything lol... damn do u know what people would do to ditch thir autos.?... crazy talk i tell you...
|
there are automatic b series trannies to use like from integra or jdm b16 auto tranny...and thats what u would need along with ecu and shifter assembly...it would prolly be easy to do...but I still dont get it
|
well i guess it's not hard but still...
|
:rolleyes:
|
JDM B16A automatic tranny from the 4 door VT-i or whatever it is over there. Good luck with your project, and remember to get a new rear tranny mount, you'll need it.
|
Originally posted by SilverSiG :richslap: what else can i say? you live in ottawa it's not like you have to deal with Toronto rushhour traffic either? i do that many days and i still have stick... if you want auto get an Si, or Dx, or Cx .. :tsk: and back to your question, would they even have a tranny that fit that engine?.... and even if they did wouldn't there be a **** load of problems with the ecu etc...? And the reason why i would want to do a Manual to Auto conversion is cause... I wouldn't be using this to mod or anything.. And I wouldn't be the only one driving it.. (not everyone can drive manual or wants to). So ... I was just wondering on inputs on Trannies. A tranny off a B18 or a B16 would be better? |
you want to trade engines and trannys? hehe
|
well, not that I would encourage this kinda behaviour... whoring out a rare and significant car, but here is the technological side of it:
Need a JDM B16A automatic ECU, a B-series auto tranny (Integra or JDM Civic), tranny mounts, torque converter, new starter, new flywheel, possibly axles (I'm not sure if the 5spd axles would fit, that's something you'd have to figure out cuz this hasn't been done before), then you need an automatic wiring harness complete interior and engine side too, auto cluster, and auto pedals, shifter assembly, shifter cables (or whatever the auto ones use), and reverse switch, and neutral/park switch, than a new JDM throttle body (possibly intake manifold). Problem is, to source all this, some used, some new, etc. plus to get someone to do the work... I'd estimating this will cost you about $3500+ because it is a LOT more difficult to add auto to a car than it is to take it away. The whole dashboard has to be ripped out and a new harness must be made/purchased (the 97-01 Integra one MAY work with some customization). The JDM wiring harness won't work cuz the wires will be the wrong length (right hand drive), and the plugs form an integra may not work. Anyways, it's a bad bad bad bad bad bad idea. Trade your car and buy a new 1.7EL acura. |
I think it would cost you less to get an Auto Si, and get all the SiR ammenities.
|
Originally posted by sketch I think it would cost you less to get an Auto Si, and get all the SiR ammenities. |
i agree......
AUTO SI. all you need is the LIP, rims, rear disk conversion.. heated mirriors, honestly i say go with a Integra LS |
Originally posted by bbarbulo well, not that I would encourage this kinda behaviour... whoring out a rare and significant car, but here is the technological side of it: Need a JDM B16A automatic ECU, a B-series auto tranny (Integra or JDM Civic), tranny mounts, torque converter, new starter, new flywheel, possibly axles (I'm not sure if the 5spd axles would fit, that's something you'd have to figure out cuz this hasn't been done before), then you need an automatic wiring harness complete interior and engine side too, auto cluster, and auto pedals, shifter assembly, shifter cables (or whatever the auto ones use), and reverse switch, and neutral/park switch, than a new JDM throttle body (possibly intake manifold). Problem is, to source all this, some used, some new, etc. plus to get someone to do the work... I'd estimating this will cost you about $3500+ because it is a LOT more difficult to add auto to a car than it is to take it away. The whole dashboard has to be ripped out and a new harness must be made/purchased (the 97-01 Integra one MAY work with some customization). The JDM wiring harness won't work cuz the wires will be the wrong length (right hand drive), and the plugs form an integra may not work. Anyways, it's a bad bad bad bad bad bad idea. Trade your car and buy a new 1.7EL acura. im using my auto axles on my 5 spd tranny and the pedals you dont need new pedals, just unbolt the clutch pedal assembly the rest stay in it would be a wiring nightmare, youd need the wiring diagram for everything to make it work |
All times are GMT -4. The time now is 02:44 PM. |
© 2024 MH Sub I, LLC dba Internet Brands