DIY EK rear sway bar
#1
Guest
Posts: n/a
DIY EK rear sway bar
Objective: Install an OE SiR Sway Bar on any 6th Generation Civic
About the mod:
Except the SiR model, all 6th Generation Civics have no Rear Sway bar (Rear Stabilizer bar, Rear Anti-roll bar, Rear anti-sway bar), whatever way you call it.
However, all 6th generation civics can install the OE SiR Rear Sway Bar easily since all 6G civics come with mounting holes that needed to complete this mod.
All parts can be ordered from any honda dealer, it costed me about $250 for everything.
Difficulit level: Relatively Easy
Tools Needed:
Jack, Jack Stands
Socket wrench with assorted sockets
Open-end wrench
Torque wrench (optional)
Time Needed: 1 hr or less
DISCLAIMER: This is only a installation that performed by me, not by professional. Therefore, I am not responsible for: (A) Wrong procedure. (B) The results of installation. (C) Any damage (car , your life or anything) during or after the installation (D) any other reponsiblilities
Parts List:
1x 27. 52300-S52-A01 SPRING, RR. STABILIZER (13MM)
2x 28. 52308-S04-000 HOLDER, RR. STABILIZER
2x 29. 52315-S52-A00 BUSH, RR. STABILIZER (13MM)
2x 30. 52317-S04-000 BRACKET, RR. STABILIZER
1x 31. 52320-S04-003 LINK ASSY., R. RR. STABILIZER
1x 32. 52321-S04-003 LINK ASSY., L. RR. STABILIZER
2x 33. 90002-S10-000 NUT, FLANGE (10MM)
2x 34. 90212-671-005 NUT, SELF-LOCK (10MM)
4x 35. 83403-0802008 BOLT-WASHER (8X20)
4x 36. 95701-0801808 BOLT, FLANGE (8X18)
Extra: 4x Self locking nuts and 4x washers
Click pics to enlarge
Fig 1: everything is here except the 4 self locking nuts and washers
STEP 1: Double Checking and make sure everything is here.
Fig 2: Bushing, bracket and endlink attached to the sway bar
STEP 2: Practice makes perfect, see how everything need to be put together
Fig 3: Everything fits perfectly
STEP 3: If everything is ready, head to the garage
Fig 4: Jack up the car, remember, SAFETY FIRST.
STEP 4: Jack up the car, jack stand alone is not safe. I use my some rims to support and make sure I don't get killed when I work under my car.
(note: removal of the rear wheels is not necessary)
Fig 5: See the 3 holes, the hole at the lower control arm is for the endlink, and the other 2 holes are for the bracket
STEP 5: Locate the factory mounting points ,clean up if necessary
Fig 6: Put the bracket on first, use the 2 BOLT-WASHER (8X20), 2 self locking nuts and 2 washers
STEP 6: Put the bracket on first, use the 2 bolt-washer, 2 self locking nuts and 2 washers. I torque it down to 40 ft-lb by a torque wrench
Fig 7: This is the right side
STEP 7: Do the same thing as step 6
Fig 8: Put everything else on
STEP 8: Lubricate the bushings, mount the Sway bar and put everything else in place. Tighten up everything
Fig 9: Right side
STEP 9: same as step 8
Fig 10: Finished!!
Step 10: Double Check everything, make sure they are all tightened up. Lower the car.
About the mod:
Except the SiR model, all 6th Generation Civics have no Rear Sway bar (Rear Stabilizer bar, Rear Anti-roll bar, Rear anti-sway bar), whatever way you call it.
However, all 6th generation civics can install the OE SiR Rear Sway Bar easily since all 6G civics come with mounting holes that needed to complete this mod.
All parts can be ordered from any honda dealer, it costed me about $250 for everything.
Difficulit level: Relatively Easy
Tools Needed:
Jack, Jack Stands
Socket wrench with assorted sockets
Open-end wrench
Torque wrench (optional)
Time Needed: 1 hr or less
DISCLAIMER: This is only a installation that performed by me, not by professional. Therefore, I am not responsible for: (A) Wrong procedure. (B) The results of installation. (C) Any damage (car , your life or anything) during or after the installation (D) any other reponsiblilities
Parts List:
1x 27. 52300-S52-A01 SPRING, RR. STABILIZER (13MM)
2x 28. 52308-S04-000 HOLDER, RR. STABILIZER
2x 29. 52315-S52-A00 BUSH, RR. STABILIZER (13MM)
2x 30. 52317-S04-000 BRACKET, RR. STABILIZER
1x 31. 52320-S04-003 LINK ASSY., R. RR. STABILIZER
1x 32. 52321-S04-003 LINK ASSY., L. RR. STABILIZER
2x 33. 90002-S10-000 NUT, FLANGE (10MM)
2x 34. 90212-671-005 NUT, SELF-LOCK (10MM)
4x 35. 83403-0802008 BOLT-WASHER (8X20)
4x 36. 95701-0801808 BOLT, FLANGE (8X18)
Extra: 4x Self locking nuts and 4x washers
Click pics to enlarge
Fig 1: everything is here except the 4 self locking nuts and washers
STEP 1: Double Checking and make sure everything is here.
Fig 2: Bushing, bracket and endlink attached to the sway bar
STEP 2: Practice makes perfect, see how everything need to be put together
Fig 3: Everything fits perfectly
STEP 3: If everything is ready, head to the garage
Fig 4: Jack up the car, remember, SAFETY FIRST.
STEP 4: Jack up the car, jack stand alone is not safe. I use my some rims to support and make sure I don't get killed when I work under my car.
(note: removal of the rear wheels is not necessary)
Fig 5: See the 3 holes, the hole at the lower control arm is for the endlink, and the other 2 holes are for the bracket
STEP 5: Locate the factory mounting points ,clean up if necessary
Fig 6: Put the bracket on first, use the 2 BOLT-WASHER (8X20), 2 self locking nuts and 2 washers
STEP 6: Put the bracket on first, use the 2 bolt-washer, 2 self locking nuts and 2 washers. I torque it down to 40 ft-lb by a torque wrench
Fig 7: This is the right side
STEP 7: Do the same thing as step 6
Fig 8: Put everything else on
STEP 8: Lubricate the bushings, mount the Sway bar and put everything else in place. Tighten up everything
Fig 9: Right side
STEP 9: same as step 8
Fig 10: Finished!!
Step 10: Double Check everything, make sure they are all tightened up. Lower the car.
Thread
Thread Starter
Forum
Replies
Last Post
Kyoshiro
Honda Civic (+ other) Parts/Accessories for Sale or Trade
5
14-Oct-2011 08:21 PM
smokeybanana
Honda Civic (+ other) Parts/Accessories for Sale or Trade
0
03-Jul-2011 03:43 PM
JLCivixHBDX
Honda Civic (+ other) Parts/Accessories for Sale or Trade
0
21-Jan-2009 06:57 PM
tegdream
Honda Civic Performance - JDM Discussion
1
14-Aug-2003 09:04 AM