Short Shifter inquiry
I need to get my clutch replaced for my 1998 Honda Civic (SI coupe) and I'm lookin' to replace the stock shifter with a short one.
I remember hearing/reading one time that apparently, Toucan Industries' (Ractive) Short Shifters suck. Now before I buy a short shifter (since the transmission place said they'll put it in for free along with the clutch replacement), I just wanted to know.... Does brand matter? Or can I get pretty much anything? (Ebay has these Tenzo brand shifters for $30 CDN.) Can anyone make any recommendations/input? Many thanks. |
i habe a b&m shifter that are good i guess i duno i never had anything else but wil mabie have 2 drop the mufler a little cus the piece from the ball 2 the shaft is longer and sticks down more at the botton and tends 2 hit the heatsink
|
[window]www.torontocivics.com/tccforums/showthread.php?s=&threadid=85478[/window]
this is all you need to know... cheap short shifters suck, many of them have snapped. I'd stick to B&M, at their price point, they represent great value. |
B&M
|
cut ur stock shifter in 5 min and u got urself a shotshifter 4 free :D
|
Cut it and you will literally have a "SHORT" shifter. Cutting your shifter does not decrease the distance that the arm will pivot, thus keeping the throws the same distance.
A short throw shifter can sit around the same height as stock, but still decrease the actual throw significantly. |
I had a short shifter, didn't like it that much, prefer the feel of stock...but you should upgrade all the bushings, that makes a big difference..
|
Originally posted by ROCKET VTEC cut ur stock shifter in 5 min and u got urself a shotshifter 4 free :D |
Originally posted by GoldBadge Cut it and you will literally have a "SHORT" shifter. Cutting your shifter does not decrease the distance that the arm will pivot, thus keeping the throws the same distance. A short throw shifter can sit around the same height as stock, but still decrease the actual throw significantly. |
Well, the shifter will still be pivoting the same amount of degrees if you just cut it down. So it's arguable....The distance your hand moves is less, but the actual throw of the shifter is still the same.
So you got a new shifter I take it, Cynikal? What did it run you if ya don't mind sharing? |
the b&m shifter kit was 80bucks
|
I've only heard good things about B&M.
|
THat's a good price... where did you get your shifter kit from Cynical?
|
tunersport in mississauga is where I picked it up...nice dude in there,hooked me up in a jam and they got nuff goodies in that place too
|
B&M
|
i just bought a B & M short shifter at Performence Parts Plus for $77 for everything , but havein't had time to install it yet.....too much fuken work
|
edelbrock :)
|
I, too jsut installed a B&M into my car, the kit comes with all the bushings, and all Ness. hardware, and uses your stock collar and gives you grease as well, I had an SPW shifter, hated it, i love this thing to DEATH, its frickin' amazing,
if nobody feels like installing it into their car, I can do it for a heck lot cheaper than eny store... but all praise to B and M....the best...you get what you pay for... just my 2 cents! Kevin |
Originally posted by Younes Si i just bought a B & M short shifter at Performence Parts Plus for $77 for everything , but havein't had time to install it yet.....too much fuken work |
B&M suck! Mine rattles like shyte. I replaced all the bushings in it and the linkage. No it;s not hitting the exhaust so that's not it either the fact is it doesn't use a sealed pivot bearing just rubber washers so there is a little bit of play. I am going to try out a skunk2 one and see how that goes. As for the throws on the B&M they are great and it shifts smoothly.
|
i say a shifter is a shifter. For what it is i couldn't justify spending $80. I got mine for a present, i think it was $20 US. Its a dual bend, IMO dual bends are way better, its cheap and very effective. Its only tops 1" shorter than the stock shifter but the throw has been reduced by 40%. It took 20 minutes to install, didn't have any issues with the exhaust which is 2.5" front to back.
What makes any difference is the bushings. I don't have the polyureathane bushings in mine and it feels very mechanical (i don't mind it, kinda used to it) b/c i just used washers, like 3 on one side and 4 on the other to hold it in place in the shift linkage. |
Originally posted by t_dot_SiR i suppose performance parts plus is in windsor since you're located in windsor... do they have any stores in toronto? installed the shifter yesterday, and DAMN, I FUKEN LOVE IT...and no Performance Parts Plus is only in windsor, but i believe you guys have a place near the gta called Focus auto or some ****, anyways, just to let tell anyone who doeisn't have a SS, if you dont' have one your missing out :drivesafe |
Originally posted by Younes Si installed the shifter yesterday, and DAMN, I FUKEN LOVE IT...and no Performance Parts Plus is only in windsor, but i believe you guys have a place near the gta called Focus auto or some ****, anyways, just to let tell anyone who doeisn't have a SS, if you dont' have one your missing out :drivesafe |
Skunk2 owNz!:p
|
Originally posted by DumbasSi Skunk2 owNz!:p |
Originally posted by 97SiR Which SS did u get, B&M? |
All times are GMT -4. The time now is 01:06 PM. |
© 2024 MH Sub I, LLC dba Internet Brands