Honda Civic Performance - JDM Discussion Engine tech, forced induction, springs, shocks, brakes, tires, etc.

Engine Question

Old 13-Aug-2006, 05:43 PM
  #1  
Registered User
Thread Starter
 
imported_Paolo's Avatar
 
Join Date: Oct 2004
Posts: 148
Engine Question

i have a b16, gen 2 in a 93 civic, what is involved to put it into a 98 hatch back, or coupe. Im just wondering what i need to do if anything, to get it in there properly. Any help would be appreciated.
imported_Paolo is offline  
Old 13-Aug-2006, 05:46 PM
  #2  
Senior Member
 
Join Date: Mar 2005
Posts: 6,176
rear tranny mount and drive side bracket from a 99-00 si-r. and all the b-series parts (axles, linkage, etc)

you'll also need a conversion harness to run a obd1 ecu
chris_si98 is offline  
Old 13-Aug-2006, 05:51 PM
  #3  
Registered User
Thread Starter
 
imported_Paolo's Avatar
 
Join Date: Oct 2004
Posts: 148
How much am i looking at for all that
imported_Paolo is offline  
Old 13-Aug-2006, 09:11 PM
  #4  
Registered User
 
Capo's Avatar
 
Join Date: Apr 2004
Location: North York/Oshawa
Posts: 469
actually you need the rear tranny bracket (T-mount) from an SiR and the Post mount that bolts to the engine block from an SiR. If the car is originally manual then everything else is bolt up.
Capo is offline  
Old 13-Aug-2006, 09:27 PM
  #5  
Senior Member
 
Join Date: Mar 2005
Posts: 6,176
All mounts from 99-00 Honda Civic SiR (US Si)
Note: The transmission mounts are for the 99-00 SiR tranny. If someone could confirm that they would also fit the Integra transmissions it would make this thread more usefull! the T-Belt mount will fit any B Series engine however.)

Timing Belt Mount
Part # 11910-P30-000
(Mount bolts to the block underneath the timimg belt cover)

Transmission Mount (top) **Update: All hydraulic trans use the same mount, therefore this mount is not required**
Part # 50825-S04-000

Rear Mount (t-shaped bracket)
Part # 50827-S04-N10

Torque Mounts left/right
I don't have these part numbers. If anyone can contribute it would be appreciated.
The transmission torque mount required will be for any Integra 94-up and Civic Si (Canadian SiR) 99-00. The A/C torque mount will be specific to the engine you have.

All three mounts retail for about $200.00 CDN direct from Honda

my mistake.
chris_si98 is offline  
Old 13-Aug-2006, 11:26 PM
  #6  
Registered User
 
Capo's Avatar
 
Join Date: Apr 2004
Location: North York/Oshawa
Posts: 469
Originally posted by chris_si98


Transmission Mount (top) **Update: All hydraulic trans use the same mount, therefore this mount is not required**
Part # 50825-S04-000

For this one its specific to the chassis/year, so manual 96-00 all share the same whereas the 92-95 all share the same but are different than the 96-00.
Capo is offline  
Old 13-Aug-2006, 11:37 PM
  #7  
Senior Member
 
Join Date: Mar 2005
Posts: 6,176
so.. if you swap on obd1 tranny into an ek.. the ek mount won't work?
chris_si98 is offline  
Old 14-Aug-2006, 12:44 AM
  #8  
Registered User
 
Capo's Avatar
 
Join Date: Apr 2004
Location: North York/Oshawa
Posts: 469
Originally posted by chris_si98
so.. if you swap on obd1 tranny into an ek.. the ek mount won't work?
nope the upper tranymission mount from an eg will not work in an EK chassis. On the EK mount the bushing is bolted to the frame whereas on the eg the bushing is on the mount on the transmission (could be the other way around)
Capo is offline  
Old 14-Aug-2006, 02:36 AM
  #9  
Senior Member
 
Join Date: Mar 2005
Posts: 6,176
so how can z6 trannys bolt right up to EK chassis mounts?
chris_si98 is offline  
Old 14-Aug-2006, 04:18 AM
  #10  
Registered User
 
Capo's Avatar
 
Join Date: Apr 2004
Location: North York/Oshawa
Posts: 469
Originally posted by chris_si98
so how can z6 trannys bolt right up to EK chassis mounts?
because you use the upper tranny mount off of your old tranny (from your EK)

here's a picture to illustrate it to you
1992-1995 Civic Upper Tranny Mount is #4 in the picture

1996-2000 Civic Upper Tranny Mount is #6 in the picture




For reference Paolo if your putting it into a 96-00 Civic with a MT already you only need #7 and the Mount in the bottom right corner listed as E-14-1.
Capo is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
xrated
Engine
4
10-Sep-2008 08:30 PM
polska_01
Honda Civic Performance - JDM Discussion
15
13-Jun-2007 11:18 PM
bluesicoupe
Honda Civic (+ other) Parts/Accessories for Sale or Trade
1
22-Oct-2004 04:41 PM
Quicksol
Honda Civic (+ other) Parts/Accessories for Sale or Trade
0
01-Jun-2004 02:28 PM


Thread Tools
Search this Thread
Quick Reply: Engine Question


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.