imported_cold_fire

i brought a front strut bar but i don't have a torque wrench to install it, anyone have one where i can come and use?

btw install is simple right? unbolt the bolt that connect the strut together and install the strut and bolt it on again?

Buff 'n Stuff

yes it is that simple.

I don't have torque wrench, but I use them at work everyday... so when I'm working on my car at home, I know approx. how tight nuts & bolts should be by the feel.

scott newman

Go buy one they arent that expensive, I cant get over all of these requests for tools. You have no idea how much you will use tools if you owned them. For a measly 40-50 bux you can pick a cheap one up at home depot or can tire or sears. Hell if you are that cheap use it then return it

imported_gatherer

I have a torque wrench ... actually I have a lot of different tools that fit in the category of "never to leave my sight" (yes I do drive with them in my car ) come to the meet tonight I'll be there

imported_loudsubz

canadian tire has the beam type torque wrenches for $22 or so, best investment

imported_GoldBadge

I heard these ones are more accurate than the clicking kind...true??

imported_loudsubz

true

but they have the downside, that you have to be able to see the scale to use them properly, so in tight places a clicker style torque wrench would be better, but they require re calibration to keep them up to spec, whereas the beam style does not.

bbarbulo

iTrader: (2)

are you kidding me?? beam types are terrible for accuracy. just look through the pile of torque wrenches at CT, you're guaranteed to find some that read +/- 5 lbs right off the bat. no way I'd ever use a beam type.

I have torque wrenches... both inch-lb and ft-lb and both are clicking type.

imported_loudsubz

yep its true, beam are more accurate and stay accurate unlike un-calibrated click types.

When clicker types are calibrated often then they are as accurate as beam type, if you see the needle not lining up at 0 then they will be off, but if you get one that is straight from new they are great.

bbarbulo

iTrader: (2)

I used to calibrate torque wrenches for QS9000 approval at a manufacturing facility. Quite frankly, I've never seen a torque wrench that was out of spec. They were all click types, and we had these massive blocks of steel where you insert the 3/8 or 1/2 inch drive, and the calibration blocks had a digital readout of the torque you put in... so you compare that to when it clicked, and you record the data for QS9000 audits. Not one torque wrench was ever out. They DO break from abuse and stuff, but if you are careful, it's fine.

imported_loudsubz

Might not have happend for you but they do go out of whack, and need to be recalibrated on a basis.

imported_cold_fire

i'll come out to the meet tonight, if anyone have a torque wrench can they bring it along

btw one question, the strut bar should be installed when the car is on flat ground or does it not matter?

punkindrublic

i'm a believer of the click type as well... i'd rather just set a rating then tighten then click i'm done... rather then lining up the bending rod...

although wouldn't that bending rod also loose its "spring" in time? cause you bend anything enough it looses its elastisity right?

i've had the same torque wrench on and off for over 2 years now... never once been calibrated... and it was in use at my dads work... and it is still within spec, mind you its not a cheapy one from CT or home depot... the retail is probably $250 but not my money

imported_Stocker

How do you know when to recalibrate the wrench? If mine is off, where do I go to recalibrate it? I have the CT one where you dial it to spec.

punkindrublic

i'm not sure how you'd do it at home my dads work has all those cool things to calibrate a slew of measurement tools... like the thing bbarbulo was talkin about up there

imported_loudsubz

you need this



as far as the beam style, as long as it lines up at 0 with no load your fine

1sloweg

i wouldnt trust any torque wrench other then snap-on. I paid 400 for mine, been using it for 4 years. Assembled countless motors with it, and went to get it calibrated the other day..... it was 0.001 ft/lbs off.

You get what you pay for.

imported_loudsubz

well any torque wrench can be off, the limit is 4% off the reading, a snap on could be off as well, just depends how it is used, and how long etc.

bbarbulo

iTrader: (2)

I keep mine in my room, in it's original box... it's just a Sears one cuz I needed it quick... and I needed BOTH of them on the same day. Eventually I'll upgrade when I gotta build a motor.

Si98

i bought a clicking type 3/8" torque wrench a few days ago from canadian tire that handles 25 to 250 inch/lbs. it cost me $89 plus taxes.

the instructions for my neuspeed front upper strut bar says to torque the nuts to only 33 inch/lbs. so here i am tightening the nuts extremely tight waiting for the wrench to "click" but it doesn't.

is there something else that i need to hear to look for to tell me to stop tightening? perhaps the torque wrench is defective?