Adding power to the DOHC ZC Engine
My new hatchback has a DOHC ZC engine
I test drove it and it's a lot stronger than my D15B2, but i am looking for a little bit more than that So this is what I am upgrading right now... Si tranny (the car comes with slow CX tranny...2000rpm at 100km/h) 11lb lightweighted flywheel NGK high output spark plugs 2.75" catback exhaust Ported T/B Ported Intake Manifold Cold Air Intake Chipped ECU ~~~~~~~~~~~~~~ so is there any other good ways to gain more power from this engine? i was so mad at myself that didn't spend a little extra money for a B18C but since i got this motor i am going to stick with it. I am looking for something that is close to B16A or faster anyone who can help? |
2.75' catback?
I have a 2.75" catback exhaust on my civic hb with ZC motor
is it a good setup? or i should go with a smaller pipe? my frd told me 2" is the best way to go, is it really slow with 2.75" pipe? |
Headers for ZC engine
I am wondering which headers will fit the DOHC ZC engines?
i heard the D sereis headers are not perfect fit to the ZC engine anyone can confirm? |
wow thats huge...my 2.0L only used a 2.5"...so ya i would go with a 2"
|
2" to 2.38" would be good size. 2.75" seems a bit too large.
|
50 shot of Nozz all day long.
|
its the down pipe of the head that might need to be modded to fit properly.
Why dont you just get some head work done? shave the head, get a valve job, if you have the money get a PP done. Tuned ECU cams, cam gears, valve train. Throwing a turbo on a ZC is rather pointless not just becuase the high compression but the top of teh pistons are dome shape and tend to blow piston rings with boosted. If you get all that work done... then your exhaust would be more benifical than pointless. |
BUDGET BOOOOOOST!
|
you have to port match the d series headers with a zc exhaust gasket. and make he ports a little bigger.
|
Vitara pistons ftw
|
Change your exhaust and get a header. I tried a Lightspeed and Genie header they both needed to be matched.
Also that chip...what is it? ZC? Mugen? |
Originally posted by SMGFANDOTCOM Change your exhaust and get a header. I tried a Lightspeed and Genie header they both needed to be matched. Also that chip...what is it? ZC? Mugen? i just found out that i am currenly on P07(VX ECU), i have no idea how they put that into my ZC and it's freaking slow!!! it runs so lean that the car just stop making power after 5500rpm and i dunno what chip, i was told it's chipped and needs to run 91octane...and it has a 8100rpm redline, but i will give it a try |
why dont you get the proper ecu first??
|
just get the right chip, or a custom tune.
|
sorry I don't exactly know that much about ZCs or what they can do but for the price of all that stuff that you're doing, can't you pick up a b18a/b or a b16a and toss it in? thats a already a nice little boost =p
|
or toss in a b16 at least :D woohaw. b series ftw!
|
man just get a nice header port match it with a nice 2 inch mandrel bent exhaust with a nice vibrant flat black sleeper muffler high flow cat with a resonator a zc ecu, nice clutch (exedy race organic). And call it a day run 15 flat to real low 15's. pepy littel dd, cause only way to go faster if to boost it. You could go buy a jackson racing zc supercharger kit or a d series greddy turbo kit. Stock internal zc can handle light boost allday long 160-170 whp all day long.
|
zc bottom end is the same as a d16 bottom end. 75mm pistons and a 90mm stroke. the bottom end can handle the same amount of power that a d series can.
|
Your car must be wiried OBD1 if you have that ECU ..post up pics of the motor and ecu
if it is just toss the zc and put in a d15b or d16z6 :thumbup: |
Originally posted by chris_v2 why dont you get the proper ecu first?? the fuel cutoff is 6500rpm btw... i got a chipped P06 ECU on hand, but haven't install yet and yes it's OBD1, what other ECUs i can use? |
All times are GMT -4. The time now is 12:36 PM. |
© 2024 MH Sub I, LLC dba Internet Brands